**Myself
Step restore client from Ignite server
1. Interrupt boot os
2. Boot ignite tape version ignite from tape = ignite server
-or-
Boot DVD media version ignite from media = ignite server
-or-
Boot lan (same subnet if not config boot-helper)
Bo lan.XX.XX.XX.XX install (XX=ip ignite server)
3. In Install Welcome sceen ,choose Ignite-UX and Advance install
4. Choose Archive file from ignite server
5. Check space ,dump file ,vg and all
6. Go ! to begin installation phase
Screen restore client from Ignite server
Welcome to the HP-UX installation/recovery process!
Use the <tab> key to navigate between fields, and the arrow keys
within fields. Use the <return/enter> key to select an item.
Use the <return/enter> or <space-bar> to pop-up a choices list. If the
menus are not clear, select the "Help" item for more information.
Hardware Summary: System Model: 9000/800/L3000-8x
+---------------------+----------------+-------------------+ [ Scan Again ]
| Disks: 8 (273.6GB) | Floppies: 0 | LAN cards: 5 |
| CD/DVDs: 1 | Tapes: 4 | Memory: 12288Mb |
| Graphics Ports: 0 | IO Buses: 17 | CPUs: 4 | [ H/W Details ]
+---------------------+----------------+-------------------+
[ Install HP-UX ]
[ Run a Recovery Shell ]
[ Advanced Options ]
[ Reboot ] [ Help ]
User Interface and Media Options
This screen lets you pick from options that will determine if an
Ignite-UX server is used, and your user interface preference.
Source Location Options:
[ ] Media only installation
[ ] Media with Network enabled (allows use of SD depots)
[ * ] Ignite-UX server based installation
User Interface Options:
[ ] Guided Installation (recommended for basic installs)
[ * ] Advanced Installation (recommended for disk and filesystem management)
[ ] No user interface - setup basic networking, use defaults and go
[ ] Remote graphical interface running on the Ignite-UX server
Hint: If you need to make LVM size changes, or want to set the
final networking parameters during the install, you will
need to use the Advanced mode (or remote graphical interface).
[ OK ] [ Cancel ] [ Help ]
LAN Interface Selection
More than one network interface was detected on the system. You
will need to select the interface to enable. Only one interface
can be enabled, and it must be the one connected to the network
that can be used in contacting the install and/or SD servers.
Use the <tab> and/or arrow keys to move to the desired LAN device
to enable, then press <Return>.
HW Path Interface Station Address Description
----------------------------------------------------------
[ 0/0/0/0 lan0 0x00306EC3B29D HP_PCI_10/100Base-TX_Core ]
[ 0/3/0/0 lan1 0x00306EEA117A HP_A5230A/B5509BA_PCI_10/100Ba ]
[ 0/8/0/0 lan2 0x00306E4AFACB HP_A5230A/B5509BA_PCI_10/100Ba ]
[ 0/9/0/0 lan3 0x00306EEA112D HP_A5230A/B5509BA_PCI_10/100Ba ]
[ 0/10/0/0 lan4 0x00306EF4E08A HP_A6825-60101_PCI_1000Base-T_ ]
NETWORK CONFIGURATION
This system's hostname: phback01
Internet protocol address (eg. 15.2.56.1) of this host: 172.17.100.64
Default gateway routing internet protocol address: 172.17.100.252
The subnet mask (eg. 255.255.248.0 or 0xfffff800): 255.255.255.0
IP address of the Ignite-UX server system: 172.18.136.116
Is this networking information only temporary? [ No ]
[ OK ] [ Cancel ] [ Help ]
* Bringing up Network (lan4)
add net default: gateway 172.17.100.252
* Reading configuration information from server...
* NFS mounting clients directory.
* Using client directory: /var/opt/ignite/clients/0x00306EF4E08A
* Creating logical volume "vg00/lvol5" (/home).
* Creating logical volume "vg00/lvol6" (/opt).
…….
* Extending logical volume "vg00/lvol1" (/stand).
…….
* Making HFS filesystem for "/stand", (/dev/vg00/rlvol1).
* Making VxFS filesystem for "/", (/dev/vg00/rlvol3).
* Making VxFS filesystem for "/tmp", (/dev/vg00/rlvol4).
…….
* Setting rotational delay to 0 for "/stand".
* Configure_Disks: Complete
* Download_mini-system: Begin
x ./sbin/fs/hfs/mkfs, 290816 bytes, 568 tape blocks
…….
./sbin/lvcreate linked to ./sbin/lvchange
…….
x ./configure3, 483328 bytes, 944 tape blocks
x ./monitor_bpr, 32768 bytes, 64 tape blocks
* Download_mini-system: Complete
* Loading_software: Begin
* Installing boot area on disk.
* Enabling swap areas.
* Backing up LVM configuration for "vg00".
* Processing the archive source (Recovery Archive).
* Fri Feb 03 03:21:29 EST 2006: Starting archive load of the source
(Recovery Archive).
* Processed 10% of archive
* Processed 20% of archive
…..
* Processed 90% of archive
* Completed 100% of archive
* Fri Feb 03 03:45:28 EST 2006: Completed archive load of the source
(Recovery Archive).
* Executing user specified script:
"/opt/ignite/data/scripts/os_arch_post_l".
* Running in recovery mode (os_arch_post_l).
* Running the ioinit command ("/sbin/ioinit -c")
* Creating device files via the insf command.
insf: Installing special files for sdisk instance 0 address 0/0/1/1.0.0
…….
insf: Installing special files for btlan instance 0 address 0/0/0/0
…….
insf: Installing special files for pseudo driver dlpi
…….
* Running "/opt/upgrade/bin/tlinstall -v" and correcting transition link
permissions.
into kernel if SCA use is desired.
* Executing: "/var/adm/sw/products/OS-Core/CORE-KRN/iux_postload".
* Executing: "/var/adm/sw/products/OS-Core/CORE-SHLIBS/iux_postload".
* No actions taken - running in recovery mode.
* Executing: "/var/adm/sw/products/PHSS_25983/pfiles/iux_postload".
NOTE: tlinstall is searching filesystem - please be patient
NOTE: Successfully completed
* Loading_software: Complete
* Build_Kernel: Begin
NOTE: Since the /stand/vmunix kernel is already in place, the kernel will
not be re-built. Note that no mod_kernel directives will be processed.
* Build_Kernel: Complete
* Boot_From_Client_Disk: Begin
* Rebooting machine as expected.
NOTE: Rebooting system.
sync'ing disks (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty
Closing open logical volumes...
Done
0 comments:
Post a Comment