** Myself
The Restore may be use DVD-Media from EFI Menu then use to tape-drive to restore
--> EFI
--> DVD boot
--> Media
--> install and advance
--> boot from tape
After boot from DVD
Welcome to the HP-UX installation/recovery process!
Use the <tab> key to navigate between fields, and the arrow keys
within fields. Use the <return/enter> key to select an item.
Use the <return/enter> or <space-bar> to pop-up a choices list. If the
menus are not clear, select the "Help" item for more information.
Hardware Summary: System Model: ia64 hp server rx2620
+---------------------+----------------+-------------------+ [ Scan Again ]
| Disks: 2 (273.5GB) | Floppies: 0 | LAN cards: 2 |
| CD/DVDs: 1 | Tapes: 1 | Memory: 4076Mb |
| Graphics Ports: 0 | IO Buses: 4 | CPUs: 2 | [ H/W Details ]
+---------------------+----------------+-------------------+
[ Install HP-UX ]
[ Run a Recovery Shell ]
[ Advanced Options ]
[ Reboot ] [ Help ]
User Interface and Media Options
This screen lets you pick from options that will determine if an
Ignite-UX server is used, and your user interface preference.
Source Location Options:
[ * ] Media only installation
[ ] Media with Network enabled (allows use of SD depots)
[ ] Ignite-UX server based installation
User Interface Options:
[ ] Guided Installation (recommended for basic installs)
[ * ] Advanced Installation (recommended for disk and filesystem management)
[ ] No user interface - use all the defaults and go
Hint: If you need to make LVM size changes, or want to set the
final networking parameters during the install, you will
need to use the Advanced mode (or remote graphical interface).
[ OK ] [ Cancel ] [ Help ]
Media Installation Selection
This screen provides an option to switch the install source
from the default CD/DVD to a recovery tape. This is helpful
for those systems and for tape devices which do not support
booting from a tape.
[ ] CD/DVD Installation
[ * ] Boot from CD/DVD, Recover from Tape
[ OK ] [ Cancel ] [ Help ]
Tape Drive Selection
There are one or more tape drives detected on the system. Insert
your recovery tape into one of the drives and then select that drive
from the list below.
Use the <tab> and/or arrow keys to move to the desired TAPE device,
then press <Return/Enter> to select.
HW Path Device File Description
----------------------------------------------------------
[ 0/1/1/1.3.0 /dev/rmt/0m HP_Ultrium_2-SCSI ]
Loading INDEX from media...
* Using client directory: /var/opt/ignite/clients/0x0018FE28C1DA
* Checking configuration for consistency...
* Loading configuration user interface, please wait...
l /opt/ignite/bin/itool () k
x l Note k x
x xlqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqk x x
x xx Message From: /opt/ignite/bin/itool () ^ x x
x xx xkx
x xx WARNING: The lan device specified in "/var/opt/ignite/CONFIG": line xxx
x xx 268, (0/0/3/0) was not discovered on the system. This could be due xxx
x xx to lack of driver support in Ignite-UX for this interface card. All xxx
x xx information specified for this device will be ignored. If you are xxx
x xx recovering this system, you may need to edit /etc/rc.config.d/netconf xxx
x xx to uncomment the entries for this interface after the system is back xxx
x xx up. xxx
x xx xxx
x xx WARNING: The lan device specified in "/var/opt/ignite/CONFIG": line xxx
x xx 269, (0/0/3/0) was not discovered on the system. This could be due xxx
x xx to lack of driver support in Ignite-UX for this interface card. All xxx
x xx information specified for this device will be ignored. If you are xxx
x xx recovering this system, you may need to edit /etc/rc.config.d/netconf xxx
x xx to uncomment the entries for this interface after the system is back xjx
x xx up. v x x
xqxqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqxqx
x x [[ OK ]] x x
mqmqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqjqj
0 comments:
Post a Comment